Intex 64417E Owner's Manual download pdf (Page 2)

151

(151) AP619A BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25” 05/10/2013

151

(151) AP619A BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25” 05/10/2013

READ AND SAVE THESE INSTRUCTIONS

Page 3

READ AND SAVE THESE INSTRUCTIONS

Page 4

6. Lie down on the airbed to test the firmness.

7. If the sleeping surface is too hard, adjust the firmness

by turning the control dial counterclockwise gradually

until air starts to exit through the air passage. See

Fig (6). Turn the control dial fully clockwise when the

desired firmness is achieved. See Fig (7). If the airbed

becomes too soft repeat step #3 thru #7 as necessary.

8. Disconnect the AC line cord from the wall socket,

place it inside the cord compartment and close the

cover. Make sure the power cords are free of twist,

kink and knot.

FIG (6)

FIG (7)

Proper inflation of the airbed.

The ambient temperatures of air have an effect on the airbed internal pressure. At low

ambient temperature the air will contract within the airbed and the airbed will feel softer:

add air as necessary. At high ambient temperature the air within the airbed will expand

significantly and the airbed will become hard and may burst: release air to avoid damage

to the airbed or to soften the feel. Do not expose the airbed to extreme temperatures (hot

or cold).

Stretching is a natural characteristic of new vinyl. During initial use, the airbed may become

soft and require additional inflation to maintain desired firmness. This is normal for the first

few days of use.

Dimensions shown are approximate and will vary due to the vinyl temperature and the air

temperature.

In no event shall Intex, their authorized agents or employees be liable for damages

(such as pin holes) to the airbed caused by negligence, ordinary wear and tear,

abuse and carelessness, or external forces.

IMPORTANT NOTE

DEFLATION

1. Open line cord compartment cover. See Fig (1).

2. Plug in the AC line cord into an AC electrical outlet. See Fig (2).

3. Turn the control dial counterclockwise until arrow points to deflation mark ( ). See

Fig (8).

Marketi

,CA 90801-14

USA

countr

ies of the wor

ld by In

rading Ltd.,u

nder l

icen

se from In

Trademarks

used in some

004 In

Recreatio

p.,

ade in Ch

na/F

brique

Chine/Hec

o en China

FIG (8)

FIG (9)

Marketi

,CA 90801-14

USA

countr

ies of the wor

ld by In

rading Ltd.,u

nder l

icen

se from In

Trademarks

sed in some

004 In

Recreatio

p.,

ade in Ch

na/F

brique

Chine/Hec

o en China

FIG (10)

INFLATION OPTION

1. If electrical power is not available then a conventional foot

or manually operated air pump can be connected to the

control dial valve for inflation. See Fig (11).

2. Turn the control dial clockwise until arrow points to the

inflation mark ( ).

3. Insert air pump nozzle to the control dial valve to inflate the

airbed.

FIG (11)

Inflate only with a low pressure inflator. Do not over inflate. Fill with cold air only.

IMPORTANT

STORAGE INSTRUCTIONS

1. Deflate the airbed following the "DEFLATION" instructions.

2. Turn the control dial counterclockwise until arrow points to deflation mark ( ). See

Fig (8).

3. Make sure the airbed is clean and dry.

4. Lay bed flat with sleeping surface facing upwards and follow the folding steps on Figs

(12 - 16). Fold the airbed loosely and avoid sharp bends, corners and creases which can

damage the airbed.

FIG (12)

FIG (13)

FIG (14)

INTEX

FIG (16)

INTEX

FIG (15)

INTEX

5. Turn the control dial fully clockwise. See Fig (10).

6. Place the airbed inside the storage bag and store in a dry, cool storage location.

en China/Gedruckt in China.

®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas

utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/

a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA

90801 • Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen

Union durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands Consumer Service 1-800-234-6839\

www.intexcorp.com

4. Press "I" to switch ON. See Fig (4).

5. When the airbed is completely deflated, begin rolling the airbed from the foot of

the airbed towards the head of the airbed where the pump is located. See Fig (9).

6. When all air is removed from the airbed, press "O" to switch OFF. See Fig (5).

7. Turn the control dial fully clockwise. See Fig (10).

8. Disconnect the AC line cord from the wall socket, place it inside the cord compart

ment and close the cover. Make sure the power cords are free of twist, kink and

knot.

FIG (5)FIG (4)

FIG (3)

Marketing Ltd.

Long Beach,CA 90801-1440 USA

countries of the world by Intex

Trading Ltd.,under license from Intex

Trademarks used in some

200

4 Intex Recreation Corp.,

ade in China/Fabrique en Chine/Hecho

en China

1 2

Comments to this Manuals

No comments

Intex 64417E Owner's Manual Page 2

Comments to this Manuals

Related products and manuals for Mattresses Intex 64417E